travisnguyen

  • 活動總數 19
  • 追蹤 0 個使用者
  • 跟隨者 0 個使用者
CLO-citizen
  • 最後一個活動
  • 投票數 3
  • 訂閱數 4
  • 成員加入日期為

活動概述

travisnguyen 的最新活動

  • travisnguyen 已評論，

    1. 社區
    2. Q&A
    3. Have big gap when use Layer Clone Over

    US Designer Support Please check attached file and give advice for this case. I hope that the sewing on top look flat. Thank a lot https://1drv.ms/u/s!AuAcyL2kNiCPmJQ8Mp0BgfVMYUOQDw?e=eNzFCD

    • 檢視評論
    • travisnguyen
    • 編輯於
    • 0 票

  • travisnguyen 已評論，

    1. 社區
    2. Q&A
    3. Have big gap when use Layer Clone Over

    Hi When I use Layer Clone Over, it will make big recess as picture below. How can I reduce this affect recess? (I want to make sewing effect flat) Thank you

  • travisnguyen 已建立貼文，

    1. 社區
    2. Q&A

    Need advice to model French Seam

    Hi I'm looking method of model this kind of seam in lounge chair. I guess it is French Seam. Need advice to model this kind of seam. Attached file. Thank   Link attached file: https://1drv.ms/u/s...

    • travisnguyen
    • 編輯於
    • 2 個跟隨者
    • 1 條評論
    • 0 票

  • travisnguyen 已評論，

    1. 社區
    2. Q&A
    3. Have big gap when use Layer Clone Over

    Thank  It worked

  • travisnguyen 已建立貼文，

    1. 社區
    2. Q&A

    Have big gap when use Layer Clone Over

      Hi When I use Layer Clone Over feature, they will make the big gap as below: Then I need to delete sewing then sew again: It will cost the time if I sew again and again. What should I do? Thank...

    • travisnguyen
    • 3 個跟隨者
    • 8 條評論
    • 0 票

  • travisnguyen 已評論，

    1. 社區
    2. Q&A
    3. Need advice to simulate detail of cushion

    thank falmouth and ottoline I will learn and try Planar feature later.

  • travisnguyen 已評論，

    1. 社區
    2. Q&A
    3. Need advice to simulate detail of cushion

    Hi Adam I can simulated. However it's too bulging in front and back.  What should I do? thank Travis

  • travisnguyen 已評論，

    1. 社區
    2. Q&A
    3. Need advice to simulate detail of cushion

    Hi falmouth Thank for your try. It look good. Could you please share the file, I could learn more about how you Fold fabric.   Thank Travis

  • travisnguyen 已建立貼文，

    1. 社區
    2. Q&A

    Need advice to simulate detail of cushion

    Hi I need advice to simulate detail of cushion as below:   Thank Travis  

    • travisnguyen
    • 3 個跟隨者
    • 12 條評論
    • 0 票

  • travisnguyen 已評論，

    1. 社區
    2. Q&A
    3. Can not finish 3D Pen with curve

    Hi ottoline Not sure, I understand right? I come back model. Subdivide more polygon then make a seam as below Re-import in Clo3d Could not snap in position of seam I try to draw curve, but still c...