ganderson

  • 活動總數 30
  • 追蹤 0 個使用者
  • 跟隨者 0 個使用者
CLO-citizen
  • 最後一個活動
  • 投票數 0
  • 訂閱數 12
  • 成員加入日期為

活動概述

ganderson 的最新活動

  • ganderson 已評論，

    1. 社區
    2. Q&A
    3. Can you get rid of the height measurement bar in my project

    Thanks!!

  • ganderson 已建立貼文，

    1. 社區
    2. Q&A

    Can you get rid of the height measurement bar in my project

    I took a height measurement of my avatar and now I can't make the green bar go awayIs there some way to make it go away?                  Thanks,                    Vonnie A.

    • ganderson
    • 2 個跟隨者
    • 2 條評論
    • 0 票

  • ganderson 已建立貼文，

    1. 社區
    2. Q&A

    How do you use the avatar editor with an avatar that you generated from and FBX file?

    I have imported an FBX file into CLO and would like to use the avatar editor to set up the measurements, etc. When I open the avatar editor it is blanked out under measurements and size, but it all...

    • ganderson
    • 2 個跟隨者
    • 1 條評論
    • 0 票

  • ganderson 已建立貼文，

    1. 社區
    2. Q&A

    Skeleton is off when I import a FBX file

    Hi I have generated a rigged avatar in 3ds Max and exported it as an fbx file. When I import it into CLO3D the skeleton is offset in the body. Anyone else seen this?

    • ganderson
    • 2 個跟隨者
    • 1 條評論
    • 0 票

  • ganderson 已評論，

    1. 社區
    2. Q&A
    3. Adding sizing to an imported FBX avatar

    I will send you my fbx file. I have generated it in 3dsMax. When I just import the fbx file it is scaled correctly. It is not set to auto scale but to  cm. When I try to use the AutoConvert to Avat...

  • ganderson 已建立貼文，

    1. 社區
    2. Q&A

    Adding sizing to an imported FBX avatar

    I am trying to make an FBX avatar that I have imported into CLO size editable. When I try to use the Auto Convert to Avatar menu the avatar is imported at the wrong scale it can't be sized. When I ...

    • ganderson
    • 2 個跟隨者
    • 3 條評論
    • 0 票

  • ganderson 已建立貼文，

    1. 社區
    2. Q&A

    Opacity in CLO 7.0

    Hi I am trying to have a muslin fabric with Opacity of 100% ( No see through) Although I have the opacity set at 100% I can still see through the fabric. Do I need to set something else?           ...

    • ganderson
    • 2 個跟隨者
    • 1 條評論
    • 0 票

  • ganderson 已評論，

    1. 社區
    2. Q&A
    3. CLO Freezes when I try to sew.

    Upgraded my video card and that seems to have solved the problem

  • ganderson 已評論，

    1. 社區
    2. Q&A
    3. CLO Freezes when I try to sew.

    OK, I've played with this some this week and this is what I found. Free sewing seems to always go to the m:n sewing in the 3D window, even for the simplest seams. In the 2D window, if I do all my f...

  • ganderson 已評論，

    1. 社區
    2. Q&A
    3. CLO Freezes when I try to sew.

    This is a new issue, just since I went to CLO 6. I am running 6.0.56. When I say freezes, I mean the program stops responding, sometime for minutes on end and my courser turns into a spinning wheel...