susanameiras

  • 活动总数 14
  • 正在关注 0 名用户
  • 关注者数 0 名用户
  • 最后的活动
  • 投票数 0
  • 订阅数 4
  • 成员加入日期

活动概览

susanameiras 的最新活动

  • susanameiras 进行了评论，

    1. 社区
    2. Q&A
    3. Trim Collision

    Hi, Indeed, I found that was the problem. As many times I use high poly avatars and everything works fine, I didn't expect this would work differently. Thank you!

  • susanameiras 进行了评论，

    1. 社区
    2. Q&A
    3. Trim Collision

    Maybe important to mention that the trim tested is an .obj saved as a trim in CLO.

  • susanameiras 创建了一个帖子，

    1. 社区
    2. Q&A

    Trim Collision

    Hi all, Is anybody who has tried to use the "Collision" for a trim? I've tried to put it 'on', but when clicking on simulation, software gets so so slow that crashes even if I only have the trim in...

    • susanameiras
    • 2 个关注者
    • 3 条评论
    • 0 票

  • susanameiras 进行了评论，

    1. 社区
    2. Q&A
    3. Fabric properties - when front is different from back

    here it's possible to see what I have obtained when I first applied a different texture. By doing the above, I just reduced my variables.

  • susanameiras 进行了评论，

    1. 社区
    2. Q&A
    3. Fabric properties - when front is different from back

    the result is the same whether I use the same or a different texture on the back. Of course I want to use a different texture and I did until I realise there was something wrong on the side view.I'...

  • susanameiras 创建了一个帖子，

    1. 社区
    2. Q&A

    Fabric properties - when front is different from back

    Dear all, I have been facing an issue while applying a different texture on the front and back side of the fabric. I've just made a simple test that was to apply a material to a pattern and then to...

    • susanameiras
    • 2 个关注者
    • 4 条评论
    • 0 票

  • susanameiras 创建了一个帖子，

    1. 社区
    2. Q&A

    batch rendering

    Dear all, Do you know if there is any way to run a batch rendering in CLO3D? I have many renderings to run through different project files and I'd like to do it in batch. Many thanks for any advice...

    • susanameiras
    • 2 个关注者
    • 1 条评论
    • 0 票

  • susanameiras 进行了评论，

    1. 社区
    2. Q&A
    3. How to animate an .obj used as a part of a garment?

    Many thanks CLO Designers! However, that solution does not really work when I start the simulation. I put the solidify at 100, I select S-Hardware, particle size 3 and 5; 2mm of thickness and the r...

  • susanameiras 进行了评论，

    1. 社区
    2. Q&A
    3. How to animate an .obj used as a part of a garment?

    Hi, Many thanks for that! Actually I found different issues when using "obj load as trim" and "obj load as avatar". I want to have the following, in which the fabric goes over a part of the trim li...

  • susanameiras 创建了一个帖子，

    1. 社区
    2. Q&A

    How to animate an .obj used as a part of a garment?

    Hi, I'd like to animate my avatar wearing clothes that hold accessories. When I use trims, garment mesh passes through the trim mesh keeping the trim over the garment, I can only use an .obj to avo...

    • susanameiras
    • 3 个关注者
    • 5 条评论
    • 0 票